Air Massage and Whirlpool Combinations

Please download to get full document.

View again

All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
 16
 
  DELUXE JET AIR THERAPEUTIC AIR Air Massage and Whirlpool Combinatis INSTALLATION AND OPERATING INSTRUCTIONS READ ALL INSTRUCTIONS CAREFULLY EFORE STARTING THE INSTALLATION OF YOUR AIR MASSAGE / COMINATION
Related documents
Share
Transcript
DELUXE JET AIR THERAPEUTIC AIR Air Massage and Whirlpool Combinatis INSTALLATION AND OPERATING INSTRUCTIONS READ ALL INSTRUCTIONS CAREFULLY EFORE STARTING THE INSTALLATION OF YOUR AIR MASSAGE / COMINATION ATH. PLEASE RECORD THE SERIAL NUMER OF YOUR AIR MASSAGE ATH AND SAVE THIS MANUAL FOR FUTURE REFERENCE. NOTE: These instructis are to be used alg with the installati instructis for ACRYLIC ATHTUS. WARNING - When using electrical products, basic precautis should always be followed, including the following:. DANGER: RISK OF ELECTRICAL SHOCK. Cnect ly to a circuit protected by a ground fault circuit interrupter, (GFCI).. Grounding is required. An equipment grounding terminal is provided in the field wiring compartment. To reduce the risk of electric shock, this terminal must be cnected to the grounding means provided in the electric supply panel with a cductor equivalent in size to the circuit cductors supplying the equipment. 3. INSTALL THIS UNIT IN ACCORDANCE WITH THE CANADIAN ELECTRICAL CODE, PART OR THE APPROPRIATE CODE IN OTHER COUNTRIES. 4. INSTALL TO PERMITACCESS FOR SERVICING. 5. Provide adequate ventilati for the motor to prevent nuisance trips of the thermal overload protecti. INSTALLATION NOTES Important: All Acrylic Air Massage baths receive a thorough water test and are carefully inspected and packed for shipment. You should check your unit for any problems. Ctact your dealer before installati. Protect the bathtub and fittings from dirt and damage by leaving the polyethylene protective film in place until installati and other related cstructi are complete. Cauti: Do not lift an air massage bath or whirlpool by its plumbing. Handle it by the bath shell ly. Access for servicing the lower/pump and Ctrols of the air massage bath must be provided (Refer to specificati drawings for locati). DO NOT remove or relocate the blower or pump from its factory-installed positi. This positi ensures proper priming, drainage, and performance of the air massage or combinati system. Relocating the blower or pump will void the warranty. NOTE: The unis for the piping at the pump the combinati units are ly to be hand tightened. Check by hand that they have not loosened during shipping. MODELS WITH INTEGRAL APRON Air massage baths with an integral apr have a removable panel in the apr for access to the blower and pump. Depending the design of the whirlpool the panel is fastened to the apr by either of the following: Strips of interlocking fabric (velcro) alg the top with plastic clips the bottom (Figure ). Screws (Figure ). In either case, to remove panel follow instructis below: Panel with strips of interlocking fabric: gently pull the panel away starting from the top. To replace the panel, positi the removable panel to lower flange and press into place against the velcro pads. Figure - Copyright 00 Mirolin Ind. The Copyright includes all ctent the document. CLIP Removable Centre Panel APRON FRAME REMOVALE PANEL VELCRO 3 INSTALLATION INSTRUCTIONS (ctinued) MODELS WITH INTEGRAL APRON Removable panel fastened with screws: Plastic cap This instructi applies to the following models ly: PHOENIX SERIES TUCSON SERIES A5 L/R SYDNEY L/R ADORA L/R KD 53 L/R VIC 53 L/R A 604T L/R TS 5 L/R PT50 L/R PT56 L/R To remove the panel, first expose the screws by removing all the 5 plastic caps. Use a flat screwdriver gently to avoid scratching the acrylic bathtub. Figure 3. Figure - Integral apr with removable panel fastened with screws Figure 4 shows the exposed screw fastened the acrylic apr. To remove the panel, loosen the screws by using a Phillip s screwdriver. Figure 5. Note: Plastic caps are color-enhanced and for illustrati purposes ly. Plastic caps are color-matched based the color of the acrylic bathtub. Figure 3 - Unplug the plastic caps Figure 4 - Exposed screw the integral apr Figure 5 - Remove the screw with a Phillip s screwdriver ELECTRICAL ELECTRICAL AND TESTING WARNING: FOLLOW ALL ELECTRICAL SAFETY REQUIREMENTS LISTED AT THE EGINNING OF THE INSTALLATION SECTION OF THIS MANUAL. Have a licensed electrician make the electrical installati to ensure that all the minimum requirements of the local electrical safety codes are met. NOTE:All ctrollers shall be fastened to an adjacent stud 0 mm (4 ) above the floor. TM R INSTALLATION INSTRUCTIONS (ctinued) WHIRLPOOL PUMP 0V, 5 A FROM SERVICE PANEL GFCI - 0V POWER SUPPLY - LACK - WHITE (NEUTRAL) - GREEN (GROUND) W G W G G W W G - 0V POWER SUPPLY - LACK - WHITE (NEUTRAL) - GREEN (GROUND) CONTROL OX (WHIRLPOOL) CONTROL OX (JET AIR) ELECTRONIC TOUCH PAD CONTROL (COMINATION) 0V, 5 A FROM SERVICE PANEL GFCI W G W G - 0V POWER SUPPLY - LACK - WHITE (NEUTRAL) - GREEN (GROUND) - 0V POWER SUPPLY - LACK - WHITE (NEUTRAL) - GREEN (GROUND) LOWER Figure 6 - Air Massage/Whirlpool Combinati Cnectis ELECTRICAL CONNECTIONS Air Massage The installati must cform to the local electrical safety codes. The following are general requirements ly, they do not cover all details or all situatis. The standard requirement is a separate 5A, 5V circuit protected by a ClassA GFCI rated for 5A. The cable from the service box is to be wires plus a ground. # 4 cductor is satisfactory for distances up to 00 ft. (30 m). For air massage, electrical cnecti is a standard class A GFCI - NEMA receptacle. Some local codes may require a discnect switch. This can be installed in the wall or near the motor in the service compartment. If installed in the wall it must be at least.5 m (5 ft.) away from the tub so that a pers in the tub cannot reach it. If installed in the service compartment it should be mounted to a stud and not directly under tub. The switch may be a standard wall switch as lg as the ampere rating is at least as great as the ampere protecti rating noted above. Air Massage / Whirlpool Combinati The air massage blower and the whirlpool pump each require a 5A, 5V circuit, that is, separate lines from the service box with Class A GFCI protecti. The cable from the service box is to be 4/ wire which is satisfactory for distances up to 00 ft. (30 m). If the local codes require a discnect switch it must be a duplex switch installed in the service compartment mounted to a stud and not directly to the tub. ELECTRONIC CONTROL, AIR MASSAGE AND COMINATION The deck mounted touch-pad ctrol the Air Massage and Combinati model is cnected to two pin plugs made at the factory. Check underneath the deck that the pin plugs are cnected accordingly. 3 IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS OPERATING INSTRUCTIONS. WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE MASSAGE ATHTU WITHOUTADULT SUPERVISION;. WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE WHIRLPOOL ATHTU UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT ODYAND HAIR ENTRAPMENT; 3. WARNING: TO AVOID INJURY, EXERCISE CARE WHEN ENTERING OR EXITING THE MASSAGE ATHTU; 4. WARNING: RISK OF ELECTRIC SHOCK; DO NOT PERMIT ELECTRIC APPLIANCES ( SUCH AS A HAIR DRYER, LAMP, TELEPHONE, RADIO OR TELEVISION) WITHIN.5 m (5 ft.) OF THIS MASSAGE ATHTU; 5. CAUTION: TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODICALLY IN ACCORDANCE WITH THE MANUFACTURER S INSTRUCTIONS; 6. WARNING: RISK OF HYPERTHERMIA AND POSSILE DROWNING: WATER TEMPERATURE IN EXCESS OF 38º C (00º F) MAY E INJURIOUS TO YOUR HEALTH. CHECKANDADJUST WATER TEMPERATURE EFORE USE. FOLLOW ALL SAFETY INSTRUCTIONS IN THIS MANUAL SAFE USE OFANAIR MASSAGE OR WHIRLPOOL Your physiological respse to a hot air massage or whirlpool bath depends your age, health and medical history. Initially, stay in the bath for a short time ly until you learn your tolerance for hot water. If you develop a headache or become dizzy or nauseous, get out at ce and cool under a shower. Get medical help if symptoms persist. Csult your doctor before you use the air massage or whirlpool for physical therapy of an injury or disorder. D t take an air massage or whirlpool bath without your doctor s csent if you are ill or pregnant, or if you suffer from high blood pressure, heart disease, or other health problems. Never take an air massage or whirlpool bath while under the influence of medicati, drugs, or alcohol. WARNING DO NOT RUN THE WHIRLPOOLPUMP UNLESS THE ATH IS FILLED WITH WATER TOA LEVELOF (50 mm) AOVE THE WHIRLPOOL FITTINGS. Use ly small amount of soap or other bath preparati in whirlpool baths, otherwise excessive foaming may occur. SUCTION DO NOT LOCK SUCTION INLET SCREEN ON WHIRLPOOL ATHS. Water is circulated back to the pump from this locati. Should the inlet screen become blocked in any way the safety sucti will engage and the pump will start cavitating. The pump will immediately shut down stopping the flow, thus releasing whatever is blocking the screen. When the screen is free of blockage, the pump will automatically start up and the system is back to normal. Under no circumstance is the pump to be used without the screen the sucti return. OPERATING CONTROLS The Air Massage and Air Massage/ Whirlpool Combinatis have electric touch pad ctrols. There is a heating element within the blower that heats the air in the reservoir to 40 C (04 F), to prevent the water from cooling too fast. It will not, under any circumstances, reheat or maintain the temperature of the bath water. NOTE: 0 minutes after the blower is shut automatically or by the / ctrol, the blower will come again for 30 secds to dry the air jets. If the tub has not been drained at the time it will be necessary to run the blower manually for 30 secds to dry the jets after the tub is drained. 4 OPERATING INSTRUCTIONS (ctinued) Whirlpool Fittings Use a finger to swivel the whirlpool jet to give the directi of flow required. Do not plug the whirlpool fittings while the pump is running. The flow of water can also be increased by turning the jet face plate clockwise and decreased by turning counterclockwise. Refer to Figure 7. Cauti: The whirlpool jets can be misadjusted to throw a stream of water out of the tub, to the floor. Drain the ath Check that the pump is not running. Drain the whirlpool bath after each use. It is not a spa that can retain its water for repeated use through ctinuous filtrati, heating and chemical treatment. Motor Protecti The blower and pump motors are equipped with a built-in thermal overload protector to shut the motor in the event the temperature becomes excessive (as a result of mechanical or electrical problems; such as low voltage, poor ventilati, overload lines, etc.). The motor will restart automatically as it cools down. FIGURE 7- ADJUSTALE FLOW WHIRLPOOL JET ELECTRONIC TOUCH PAD CONTROL Air Massage Deluxe Press this key to start or stop the blower. They always start at maximum speed. Press and hold this key to increase or decrease the blower speed until desired level. TM R st press, speed will vary gradually from maximum to minimum and back to maximum. nd press, system turns and, alternately. 3rd press, returns to maximum speed. The system will stop automatically after 0 minutes. Advanced functi: An automatic drying cycle will start 0 minutes after the blower is turned. Air Massage Deluxe and Whirlpool Combinati Press this key to start the pump. They always start at maximum speed. Press this key to stop the pump. Press this key to start or stop the blower. They always start at maximum speed. TM R Press and hold this key to increase or decrease the blower speed until desired level. st press, speed will vary gradually from maximum to minimum and back to maximum. nd press, system turns and, alternately. 3rd press, returns to maximum speed. The system will stop automatically after 0 minutes. Advanced functi: An automatic drying cycle will start 0 minutes after the blower is turned. 5 OPERATING INSTRUCTIONS (ctinued) IN-LINE ATH HEATER (Optial) INTRODUCTION Your AquaHeat Whirlpool ath Heater utilizes Smart Technology to er you years of bathing pleasure. The advanced electric design provides trouble free operati and precise ctrol of water temperature. There are no adjustments necessary, after the whirlpool is filled with hot water the advanced AquaHeat Whirlpool ath Heater will maintain 04 F water temperature. To cool the water simply add cold water as desired. NOTE: The whirlpool must be running for the Heater to functi - It is ctrolled by a vacuum switch. High Limit Protecti In the event the water temperature exceeds 4 F the heater will automatically shut-. To reset, wait until the water temperature drops below 04 F, then remove power from the heater by resetting the circuit breaker at the main electrical panel. If the High-Limit trips frequently, ctact a qualified service technician. - LACK G - GREEN W - WHITE W G Specificatis:.5 kw Inline 5 Volt, 0Amp Vacuum switch Vacuum Switch In the event the pump is not running or if there is not sufficient flow, the heater will not turn ON. To correct ctact a qualified service technician. IMPORTANT ELECTRICAL INSTRUCTIONS WARNING - when using electrical products, basic precautis should always be followed including the following: DANGER: RISK OF ELECTRIC SHOCK. Cnect ly to a circuit protected by a ground fault circuit interrupter, (GFCI). Use copper cductors ly. Grounding is required. Make certain the Heater and Pump are properly grounded and the pump is ONDED as required. The heater must be installed by a qualified electrician in accordance with the Natial Electrical Code and any local codes. CAUTION efore operating the pump/heater, test the GFCI by pressing the TEST butt, the pump and heater should not operate. To resume operati press the RESET butt. If the GFCI fails to operate as described above, there is ground current flowing, DO NOT operate the pump/heater until this cditi is corrected. ELECTRICAL CONNECTION FROM SUCTION ranch Circuit 0A/5V TEST GFCI W G TO JETS HOT - LACK GND - GREEN COM - WHITE PUMP INSTALLATION: IN-LINE FROM SUCTION VERSION 6 OPERATING INSTRUCTIONS (ctinued) IMPORTANT SAFETY INSTRUCTIONS WARNING - When using this unit, basic precautis should always be followed, including the following:. READ AND FOLLOW ALL INSTRUCTIONS.. DANGER - To reduce the risk of drowning, do not permit children to use the whirlpool bath unless they are supervised by an adult at all times. 3. Use this heater for its intended use as described in this Manual. Do not alter this heater or electrical shock may occur. 4. Do not operate the Whirlpool bath or this heater with sucti covers removed, make certain the sucti covers are properly installed before use. 5. The heater must be cnected to a supply circuit that is protected by a ground fault circuit interrupter, (GFCI). The GFCI should be provided by the installer and should be tested a routine basis. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above normal body temperature of 98.6 F. The symptoms of hyperthermia include: a)an increase in the internal temperature of the body b) Dizziness c) Fainting The effects of hyperthermia include: a) Failure to perceive heat b) Failure to recognize the need to exit the bath c) Unawareness of impending hazard d) Fetal damage in pregnant women e) Physical inability to exit the bath f) Uncsciousness resulting in the danger of drowning WARNING - Use of alcohol, drugs or medicati can greatly increase the risk of fatal hyperthermia. To Test the GFCI press the TEST butt, the pump and heater should NOT operate. Press the RESET butt and the pump and heater should resume operati. If the GFCI fails to operate in this manner, there is a ground current flowing, indicating the possibility of an electrical shock. DO NOT use the pump and heater. Have the problem corrected by a qualified electrician before using. 6. Prolged immersi in hot water may induce hyperthermia. The causes, symptoms, and effects of hyperthermia may be described as follows: 7. To avoid potential damage: pregnant or possibly pregnant women should csult a physician before using the whirlpool. Water temperature in excess 00 F is not recommended. 8. The bath water temperature should not exceed 04 F. Lower temperatures are recommended for extended use (0-5 minutes) and are definitely recommended for younger children. MAINTENANCE INSTRUCTIONS Air Massage The 30 secd drying cycle after the tub is drained is important and is automatic after the air massage. If the tub was used as a regular bath or the combinati model was used ly as a whirlpool, the air massage must be turned manually for 30 secds after the tub is emptied. Whirlpool Sucti Fittings On the combinati whirlpool system, the sucti screen is the e shown in Figure 8. Should the fitting require cleaning, remove the screw from the sucti cover screen. Pull the cover and remove any lint or other material. When replacing the cover, make sure that the screw registers. Put the screw back in place and tighten to ensure there is no gap between the tub wall and sucti cover. SUCTION WALL FITTING SUCTION COVER SCREEN Figure 8- SUCTION RETURN FITTING 7 MAINTENANCE INSTRUCTIONS (ctinued) Clean and Purge Warning! The internal piping of your whirlpool must be cleaned regularly in order to reduce build up of dirt, scum and the like. This must be de even if you ly use the tub for bathing or soaking and you do not use the jets. Use the following clean and purge procedure at least every week, if the tub is used daily, or every third use, if the use is intermittent or occasial. With the tub filled with bathing temperature water to above the level of the jets, add cup of Electrasol Lem Scented Gel - Advanced Cleaning Power dishwashing detergent. To save water, you can add the detergent to the tub after use, before draining. Run the pump and jets for 0 minutes. Drain the tub. Refill the tub with fresh warm water to a level above the jets. Run the pump and jets for 5 minutes. Drain the tub. Acrylic Surface The acrylic sheet which forms the surface of your bathtub provides e of the most durable surfaces found in the modern bathroom. Keep it bright and smooth with mild liquid household detergent, soap and water, or foaming cleansers, NEVER USE aromatic solvents, abrasive cleaners, scouring compounds or pads, strg liquid cleansers, or other material that could damage or dull the surface of the bath. We recommend the periodic use of Mirogloss Acrylic and Fiberglass polish to preserve the appearance of your bath. Mirogloss Acrylic and Fiberglass polish is available from your dealer. Restoring Surface Gloss Restore surface gloss by applying a very fine rubbing compound and polishing the surface by hand or with a power buffer. Finish with an applicati of Mirogloss or a good quality automotive wax. Minor Repairs to Surface Remove minor scratches and scuffs as follows. First, wet sand the area with 600 grit wet sandpaper until the surface is smooth. Then, restore the gloss as described under RESTORING SURFACE GLOSS. Special Finishes Fittings DO NOT USE powders, pads, or liquids that ctain abrasives. Many household cleansers, including detergents for automatic dishwashers, are abrasive, and would damage the plated or coloured surfaces as well as the finish of the acrylic bath. TROULESHOOTING lower fails to operate:. Verify that electric touch ctrol is cnected. properly. Check electric power supply. Reset circuit 3. breaker or replace fuse if necessary. Check ground fault circuit interrupter. Reset if 4. tripped. If the system has been functiing for sometime, it is possible that the thermal protecti has shut the motor. Switch the system and wait for at least 30 minutes before using it again. Motor runs, but no air comes through the jets:. Verify that the main air hose from the manifold to blower is properly cnected. If necessary, recnect and tighten clamps. Air outlets of jet heads are obstructed:. If the air outlets of a jet head are obstructed by soap or other residues, fill tub with warm water, brush the jets gently with an old toothbrush, then switch system ON and OFF several times. lowing air seems to be cool.. If your tub
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks